NSLU2-Linux
view · edit · print · history

OpenEmbedded.OEKernelBuildWithStockRamdiskLog History

Hide minor edits - Show changes to markup

September 21, 2004, at 10:01 PM by ka6sox --
Changed line 1 from:
 RedBoot> exec 0x01d00000
to:
 RedBoot> exec 0x01d00000
Changed lines 5-6 from:
 CPU: XScale?-IXP425/IXC1100? revision 1
 Machine: Intel IXDP425? Development Platform
to:
 CPU: XScale-IXP425/IXC1100 revision 1
 Machine: Intel IXDP425 Development Platform
Changed line 15 from:
 Calibrating delay loop... 131.48 BogoMIPS?
to:
 Calibrating delay loop... 131.48 BogoMIPS
Changed lines 43-44 from:
 ttyS00 at 0xff000003 (irq = 15) is a XScale? UART
 ttyS01 at 0xff001003 (irq = 13) is a XScale? UART
to:
 ttyS00 at 0xff000003 (irq = 15) is a XScale UART
 ttyS01 at 0xff001003 (irq = 13) is a XScale UART
Changed lines 51-52 from:
 Creating 4 MTD partitions on "IXP425 Flash":
 0x00000000-0x00040000 : "RedBoot "
to:
 Creating 4 MTD partitions on "IXP425 Flash":
 0x00000000-0x00040000 : "RedBoot "
Changed lines 83-85 from:
 i2c-dev.o: Registered 'IXP425 I2C? Adapter' as minor 0
 i2c-core.o: adapter IXP425 I2C? Adapter registered as adapter 0.
 NET4?: Linux TCP/IP 1.0 for NET4?.0
to:
 i2c-dev.o: Registered 'IXP425 I2C Adapter' as minor 0
 i2c-core.o: adapter IXP425 I2C Adapter registered as adapter 0.
 NET4: Linux TCP/IP 1.0 for NET4?.0
Changed line 90 from:
 NET4?: Unix domain sockets 1.0/SMP for Linux NET4?.0.
to:
 NET4?: Unix domain sockets 1.0/SMP for Linux NET4.0.
Changed line 115 from:
 ixp425_eth: CPU clock speed (approx) = 0 MHz?
to:
 ixp425_eth: CPU clock speed (approx) = 0 MHz
Changed lines 119-120 from:
 31 port connect!!!!!
   Vendor: Maxtor 4  Model: R060L0?            Rev: RAMC
to:
 31 port connect!!!!!=]
   Vendor: Maxtor 4  Model: [=R060L0?            Rev: RAMC
Changed line 136 from:
 BusyBox? v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash)
to:
 BusyBox v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash)
Changed lines 148-149 from:
 X1226: found X1226 on IXP425 I2C? Adapter
 i2c-core.o: client [X1226] registered to adapter [IXP425 I2C? Adapter](pos. 0).
to:
 X1226: found X1226 on IXP425 I2C? Adapter
 i2c-core.o: client [X1226] registered to adapter [IXP425 I2C? Adapter](pos. 0).
Changed line 158 from:
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
to:
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
Changed line 163 from:
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
to:
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
Changed line 167 from:
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
to:
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
Changed line 195 from:
 LKG0FB7A9?: boot complete!
to:
 LKG0FB7A9: boot complete!
Changed line 203 from:
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
to:
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
Changed line 214 from:
 BusyBox? v0.60.4 (2004.05.28-07:40+0000) multi-call binary
to:
 BusyBox v0.60.4 (2004.05.28-07:40+0000) multi-call binary
September 21, 2004, at 09:39 AM by dyoung --
Changed lines 1-195 from:

RedBoot> exec 0x01d00000 Using base address 0x01d00000 and length 0x000be730 Uncompressing Linux.................................................... done, booting the kernel. Linux version 2.4.22-xfs (dereky@localhost) (gcc version 3.4.2) #1 Sun Sep 19 20:44:21 HST 2004 CPU: XScale?-IXP425/IXC1100? revision 1 Machine: Intel IXDP425? Development Platform Warning: bad configuration page, trying to continue Security risk: creating user accessible mapping for 0x60000000 at 0xff00f000 Security risk: creating user accessible mapping for 0x51000000 at 0xf1000000 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/ram0 initrd=0x01000000,10M mem=32M@0x00000000 console=ttyS0,115200n8 Calibrating delay loop... 131.48 BogoMIPS? Memory: 32MB = 32MB total Memory: 20420KB available (1235K code, 245K data, 236K init) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX PCI Autoconfig: Found Bus 0, Device 1, Function 0 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000 PCI Autoconfig: Found Bus 0, Device 1, Function 1 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000 PCI Autoconfig: Found Bus 0, Device 1, Function 2 PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00 PCI: bus0: Fast back to back transfers disabled Linux NET4?.0 for Linux 2.4 Based upon Swansea University Computer Society NET3?.039 Initializing RT netlink socket Starting kswapd VFS: Disk quotas vdquot_6.5.1 Journalled Block Device driver loaded i2c-core.o: i2c core module i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830) pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0xff000003 (irq = 15) is a XScale? UART ttyS01 at 0xff001003 (irq = 13) is a XScale? UART RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize SCSI subsystem driver Revision: 1.00

  • host:<NULL>

cfi_cmdset_0001: Erase suspend on write enabled Using buffer write method Using static MTD partitions. Creating 4 MTD partitions on "IXP425 Flash": 0x00000000-0x00040000 : "RedBoot " 0x00040000-0x00060000 : "System Configuration" 0x00060000-0x00160000 : "Kernel" 0x00160000-0x00800000 : "Ramdisk" usb.c: registered new driver hub pci probe begin ehci_hcd 00:01.2: NEC Corporation USB 2.0 ehci_hcd 00:01.2: irq 26, pci mem c3801f00 usb.c: new USB bus registered, assigned bus number 1 PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW. PCI: 00:01.2 PCI cache line size corrected to 32. ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4 hub.c: USB hub found hub.c: 5 ports detected pci probe ok host/usb-uhci.c: $Revision: 1.1 $ time 20:45:36 Sep 19 2004 host/usb-uhci.c: High bandwidth mode enabled host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver host/usb-ohci.c: USB OHCI at membase 0xc3809000, IRQ 28 host/usb-ohci.c: usb-00:01.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 3 ports detected host/usb-ohci.c: USB OHCI at membase 0xc380f000, IRQ 27 host/usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. i2c-dev.o: Registered 'IXP425 I2C? Adapter' as minor 0 i2c-core.o: adapter IXP425 I2C? Adapter registered as adapter 0. NET4?: Linux TCP/IP 1.0 for NET4?.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) IP-Config: No network devices available. NET4?: Unix domain sockets 1.0/SMP for Linux NET4?.0. NetWinder? Floating Point Emulator V0.97 (double precision) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 10240K VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 236K Insmod ixp400 Using /lib/modules/2.4.22-xfs/kernel/drivers/ixp400/ixp400.o hub.c: new USB device 00:01.2-1, assigned address 2 Protocol: Transparent SCSI before kernel thread Warning: loading ixp400 will taint the kernel: no license

  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
  • detect:usb-storage
  • scsi_register: usb-storage-1,
  • scsi_reg, hostno:1 prot is 49
  • scsi_reg, retval->host_no:1

scsi1 : SCSI emulation for USB Mass Storage devices

scan_scsis

Module init. Insmod ixp425 Using /lib/modules/2.4.22-xfs/kernel/drivers/net/ixp425_eth.o do read capacity!!! ixp425_eth: Initializing IXP425 NPE Ethernet driver software v. 1.1 ixp425_eth: CPU clock speed (approx) = 0 MHz?

 read capacity ok!!!

The capacity is 120103201

  • 49

31 port connect!!!!!

  Vendor: Maxtor 4  Model: R060L0?            Rev: RAMC
  Type:   Direct-Access                      ANSI SCSI revision: 02

the host no is 1

  • sd_attach:0

Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 SCSI device sda: 120103201 512-byte hdwr sectors (61493 MB) Partition check:

 sda: sda1 sda2 sda3

[error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201 ixp425_eth: ixp0 is using the PHY at address 0 ixp425_eth: ixp1 is using the PHY at address 1 ixp425_eth: ixEthMiiLinkStatus failed on PHY0?.

        Can't determine

the auto negotiated parameters. Using default values.

BusyBox? v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands.

  1. Creating ramfs for /var/lock/samba:

Limit the space of log folder: Starting Hostname :

                                                                OK

Starting Modules : Using /lib/modules/pbuttons.o Using /lib/modules/2.4.22-xfs/kernel/drivers/char/x1226-rtc.o X1226: I2C? based RTC driver. i2c-core.o: driver X1226 registered. X1226: found X1226 on IXP425 I2C? Adapter i2c-core.o: client [X1226] registered to adapter [IXP425 I2C? Adapter](pos. 0). atr is 1f enable_irq(22) unbalanced from c38b11bc Using /lib/modules/rbuttons.o Starting Modules : Setting LAN media type : Starting Set CGI_ds.conf: kjournald starting. Commit interval 5 seconds EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal EXT3?-fs: recovery complete. EXT3?-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal EXT3?-fs: recovery complete. EXT3?-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal EXT3?-fs: mounted filesystem with ordered data mode. Setting up swapspace version 0, size = 65007616 bytes Adding Swap: 63484k swap-space (priority -1)

                                                                OK

Restore time and timezone: 09/20/2004-23:04:22

                                                                OK

Restore usrgrpshares:

                                                                OK

Generating telnet password:

                                                                OK

Starting WEB Server:

                                                                OK
                                                                OK

Starting samba: Starting download: download uses obsolete (PF_INET,SOCK_PACKET) ixp425_eth: ixp0: Entering promiscuous mode device ixp0 entered promiscuous mode Starting INET Server:

                                                                OK

Creating ramfs for /tmp: Starting QuickSet? Daemon :

                                                                OK
                                                                OK

Starting Crond : Starting Rest Task : LKG0FB7A9?: boot complete!

to:
 RedBoot> exec 0x01d00000
 Using base address 0x01d00000 and length 0x000be730
 Uncompressing Linux.................................................... done, booting the kernel.
 Linux version 2.4.22-xfs (dereky@localhost) (gcc version 3.4.2) #1 Sun Sep 19 20:44:21 HST 2004
 CPU: XScale?-IXP425/IXC1100? revision 1
 Machine: Intel IXDP425? Development Platform
 Warning: bad configuration page, trying to continue
 Security risk: creating user accessible mapping for 0x60000000 at 0xff00f000
 Security risk: creating user accessible mapping for 0x51000000 at 0xf1000000
 On node 0 totalpages: 8192
 zone(0): 8192 pages.
 zone(1): 0 pages.
 zone(2): 0 pages.
 Kernel command line: root=/dev/ram0 initrd=0x01000000,10M mem=32M@0x00000000 console=ttyS0,115200n8
 Calibrating delay loop... 131.48 BogoMIPS?
 Memory: 32MB = 32MB total
 Memory: 20420KB available (1235K code, 245K data, 236K init)
 Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
 Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
 Mount cache hash table entries: 512 (order: 0, 4096 bytes)
 Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
 Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
 POSIX conformance testing by UNIFIX
 PCI Autoconfig: Found Bus 0, Device 1, Function 0
 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000
 PCI Autoconfig: Found Bus 0, Device 1, Function 1
 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000
 PCI Autoconfig: Found Bus 0, Device 1, Function 2
 PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00
 PCI: bus0: Fast back to back transfers disabled
 Linux NET4?.0 for Linux 2.4
 Based upon Swansea University Computer Society NET3?.039
 Initializing RT netlink socket
 Starting kswapd
 VFS: Disk quotas vdquot_6.5.1
 Journalled Block Device driver loaded
 i2c-core.o: i2c core module
 i2c-dev.o: i2c /dev entries driver module
 i2c-core.o: driver i2c-dev dummy driver registered.
 i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830)
 pty: 256 Unix98 ptys configured
 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
 ttyS00 at 0xff000003 (irq = 15) is a XScale? UART
 ttyS01 at 0xff001003 (irq = 13) is a XScale? UART
 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
 SCSI subsystem driver Revision: 1.00
 * host:<NULL>
 cfi_cmdset_0001: Erase suspend on write enabled
 Using buffer write method
 Using static MTD partitions.
 Creating 4 MTD partitions on "IXP425 Flash":
 0x00000000-0x00040000 : "RedBoot "
 0x00040000-0x00060000 : "System Configuration"
 0x00060000-0x00160000 : "Kernel"
 0x00160000-0x00800000 : "Ramdisk"
 usb.c: registered new driver hub
 pci probe begin
 ehci_hcd 00:01.2: NEC Corporation USB 2.0
 ehci_hcd 00:01.2: irq 26, pci mem c3801f00
 usb.c: new USB bus registered, assigned bus number 1
 PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
 PCI: 00:01.2 PCI cache line size corrected to 32.
 ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
 hub.c: USB hub found
 hub.c: 5 ports detected
 pci probe ok
 host/usb-uhci.c: $Revision: 1.1 $ time 20:45:36 Sep 19 2004
 host/usb-uhci.c: High bandwidth mode enabled
 host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
 host/usb-ohci.c: USB OHCI at membase 0xc3809000, IRQ 28
 host/usb-ohci.c: usb-00:01.0, NEC Corporation USB
 usb.c: new USB bus registered, assigned bus number 2
 hub.c: USB hub found
 hub.c: 3 ports detected
 host/usb-ohci.c: USB OHCI at membase 0xc380f000, IRQ 27
 host/usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2)
 usb.c: new USB bus registered, assigned bus number 3
 hub.c: USB hub found
 hub.c: 2 ports detected
 Initializing USB Mass Storage driver...
 usb.c: registered new driver usb-storage
 USB Mass Storage support registered.
 i2c-dev.o: Registered 'IXP425 I2C? Adapter' as minor 0
 i2c-core.o: adapter IXP425 I2C? Adapter registered as adapter 0.
 NET4?: Linux TCP/IP 1.0 for NET4?.0
 IP Protocols: ICMP, UDP, TCP, IGMP
 IP: routing cache hash table of 512 buckets, 4Kbytes
 TCP: Hash tables configured (established 2048 bind 4096)
 IP-Config: No network devices available.
 NET4?: Unix domain sockets 1.0/SMP for Linux NET4?.0.
 NetWinder? Floating Point Emulator V0.97 (double precision)
 RAMDISK: Compressed image found at block 0
 Freeing initrd memory: 10240K
 VFS: Mounted root (ext2 filesystem) readonly.
 Freeing init memory: 236K
 Insmod ixp400
 Using /lib/modules/2.4.22-xfs/kernel/drivers/ixp400/ixp400.o
 hub.c: new USB device 00:01.2-1, assigned address 2
 Protocol: Transparent SCSI
 before kernel thread
 Warning: loading ixp400 will taint the kernel: no license
   See http://www.tux.org/lkml/#export-tainted for information about tainted modules
 *** detect:usb-storage
 * scsi_register: usb-storage-1,
 * scsi_reg, hostno:1 prot is 49
 * scsi_reg, retval->host_no:1
 scsi1 : SCSI emulation for USB Mass Storage devices
 ! scan_scsis
 Module init.
 Insmod ixp425
 Using /lib/modules/2.4.22-xfs/kernel/drivers/net/ixp425_eth.o
 do read capacity!!!
 ixp425_eth:
 Initializing IXP425 NPE Ethernet driver software v. 1.1
 ixp425_eth: CPU clock speed (approx) = 0 MHz?
  read capacity ok!!!
 The capacity is 120103201
 *** 49
 31 port connect!!!!!
   Vendor: Maxtor 4  Model: R060L0?            Rev: RAMC
   Type:   Direct-Access                      ANSI SCSI revision: 02
 the host no is 1
 * sd_attach:0
 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
 SCSI device sda: 120103201 512-byte hdwr sectors (61493 MB)
 Partition check:
  sda: sda1 sda2 sda3
 [error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201
 ixp425_eth: ixp0 is using the PHY at address 0
 ixp425_eth: ixp1 is using the PHY at address 1
 ixp425_eth: ixEthMiiLinkStatus failed on PHY0?.
         Can't determine
 the auto negotiated parameters. Using default values.  


 BusyBox? v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash)
 Enter 'help' for a list of built-in commands. 

 # Creating ramfs for /var/lock/samba:
 Limit the space of log folder:
 Starting Hostname :
                                                                OK
 Starting Modules :
 Using /lib/modules/pbuttons.o
 Using /lib/modules/2.4.22-xfs/kernel/drivers/char/x1226-rtc.o
 X1226: I2C? based RTC driver.
 i2c-core.o: driver X1226 registered.
 X1226: found X1226 on IXP425 I2C? Adapter
 i2c-core.o: client [X1226] registered to adapter [IXP425 I2C? Adapter](pos. 0).
 atr is 1f
 enable_irq(22) unbalanced from c38b11bc
 Using /lib/modules/rbuttons.o
 Starting Modules :
 Setting LAN media type :
 Starting Set CGI_ds.conf:
 kjournald starting.  Commit interval 5 seconds
 EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
 EXT3?-fs: recovery complete.
 EXT3?-fs: mounted filesystem with ordered data mode.
 kjournald starting.  Commit interval 5 seconds
 EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
 EXT3?-fs: recovery complete.
 EXT3?-fs: mounted filesystem with ordered data mode.
 kjournald starting.  Commit interval 5 seconds
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
 EXT3?-fs: mounted filesystem with ordered data mode.
 Setting up swapspace version 0, size = 65007616 bytes
 Adding Swap: 63484k swap-space (priority -1)
                                                                OK
 Restore time and timezone:
 09/20/2004-23:04:22
                                                                OK
 Restore usrgrpshares:
                                                                OK
 Generating telnet password:
                                                                OK
 Starting WEB Server:
                                                                OK
                                                                OK
 Starting samba:
 Starting download:
 download uses obsolete (PF_INET,SOCK_PACKET)
 ixp425_eth: ixp0: Entering promiscuous mode
 device ixp0 entered promiscuous mode
 Starting INET Server:
                                                                OK
 Creating ramfs for /tmp:
 Starting QuickSet? Daemon :
                                                                OK
                                                                OK
 Starting Crond :
 Starting Rest Task :
 LKG0FB7A9?: boot complete!
Changed line 197 from:
 This may take some time.
to:
  This may take some time.
Changed lines 199-214 from:

OK Checking disk status : USB HDD attached EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal Done. Turning on quota.

  1. df

Filesystem 1k-blocks Used Available Use% Mounted on rootfs 9911 8919 890 91% / /dev/ram0 9911 8919 890 91% / /dev/sda1 58920100 1103776 57217728 2% /share/hdd/data /dev/sda2 123955 25341 97334 21% /share/hdd/conf

  1. busybox

BusyBox? v0.60.4 (2004.05.28-07:40+0000) multi-call binary

to:
 OK
 Checking disk status :
 USB HDD attached
 EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended
 EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
 Done.
 Turning on quota. 

 # df
 Filesystem           1k-blocks      Used Available Use% Mounted on
 rootfs                    9911      8919       890  91% /
 /dev/ram0                 9911      8919       890  91% /
 /dev/sda1             58920100   1103776  57217728   2% /share/hdd/data
 /dev/sda2               123955     25341     97334  21% /share/hdd/conf
 # busybox
 BusyBox? v0.60.4 (2004.05.28-07:40+0000) multi-call binary
Changed line 216 from:

[...]

to:
 [...] 
September 21, 2004, at 09:34 AM by dyoung --
Changed lines 1-216 from:
to:

RedBoot> exec 0x01d00000 Using base address 0x01d00000 and length 0x000be730 Uncompressing Linux.................................................... done, booting the kernel. Linux version 2.4.22-xfs (dereky@localhost) (gcc version 3.4.2) #1 Sun Sep 19 20:44:21 HST 2004 CPU: XScale?-IXP425/IXC1100? revision 1 Machine: Intel IXDP425? Development Platform Warning: bad configuration page, trying to continue Security risk: creating user accessible mapping for 0x60000000 at 0xff00f000 Security risk: creating user accessible mapping for 0x51000000 at 0xf1000000 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/ram0 initrd=0x01000000,10M mem=32M@0x00000000 console=ttyS0,115200n8 Calibrating delay loop... 131.48 BogoMIPS? Memory: 32MB = 32MB total Memory: 20420KB available (1235K code, 245K data, 236K init) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX PCI Autoconfig: Found Bus 0, Device 1, Function 0 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000 PCI Autoconfig: Found Bus 0, Device 1, Function 1 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000 PCI Autoconfig: Found Bus 0, Device 1, Function 2 PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00 PCI: bus0: Fast back to back transfers disabled Linux NET4?.0 for Linux 2.4 Based upon Swansea University Computer Society NET3?.039 Initializing RT netlink socket Starting kswapd VFS: Disk quotas vdquot_6.5.1 Journalled Block Device driver loaded i2c-core.o: i2c core module i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830) pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0xff000003 (irq = 15) is a XScale? UART ttyS01 at 0xff001003 (irq = 13) is a XScale? UART RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize SCSI subsystem driver Revision: 1.00

  • host:<NULL>

cfi_cmdset_0001: Erase suspend on write enabled Using buffer write method Using static MTD partitions. Creating 4 MTD partitions on "IXP425 Flash": 0x00000000-0x00040000 : "RedBoot " 0x00040000-0x00060000 : "System Configuration" 0x00060000-0x00160000 : "Kernel" 0x00160000-0x00800000 : "Ramdisk" usb.c: registered new driver hub pci probe begin ehci_hcd 00:01.2: NEC Corporation USB 2.0 ehci_hcd 00:01.2: irq 26, pci mem c3801f00 usb.c: new USB bus registered, assigned bus number 1 PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW. PCI: 00:01.2 PCI cache line size corrected to 32. ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4 hub.c: USB hub found hub.c: 5 ports detected pci probe ok host/usb-uhci.c: $Revision: 1.1 $ time 20:45:36 Sep 19 2004 host/usb-uhci.c: High bandwidth mode enabled host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver host/usb-ohci.c: USB OHCI at membase 0xc3809000, IRQ 28 host/usb-ohci.c: usb-00:01.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 3 ports detected host/usb-ohci.c: USB OHCI at membase 0xc380f000, IRQ 27 host/usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. i2c-dev.o: Registered 'IXP425 I2C? Adapter' as minor 0 i2c-core.o: adapter IXP425 I2C? Adapter registered as adapter 0. NET4?: Linux TCP/IP 1.0 for NET4?.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) IP-Config: No network devices available. NET4?: Unix domain sockets 1.0/SMP for Linux NET4?.0. NetWinder? Floating Point Emulator V0.97 (double precision) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 10240K VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 236K Insmod ixp400 Using /lib/modules/2.4.22-xfs/kernel/drivers/ixp400/ixp400.o hub.c: new USB device 00:01.2-1, assigned address 2 Protocol: Transparent SCSI before kernel thread Warning: loading ixp400 will taint the kernel: no license

  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
  • detect:usb-storage
  • scsi_register: usb-storage-1,
  • scsi_reg, hostno:1 prot is 49
  • scsi_reg, retval->host_no:1

scsi1 : SCSI emulation for USB Mass Storage devices

scan_scsis

Module init. Insmod ixp425 Using /lib/modules/2.4.22-xfs/kernel/drivers/net/ixp425_eth.o do read capacity!!! ixp425_eth: Initializing IXP425 NPE Ethernet driver software v. 1.1 ixp425_eth: CPU clock speed (approx) = 0 MHz?

 read capacity ok!!!

The capacity is 120103201

  • 49

31 port connect!!!!!

  Vendor: Maxtor 4  Model: R060L0?            Rev: RAMC
  Type:   Direct-Access                      ANSI SCSI revision: 02

the host no is 1

  • sd_attach:0

Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 SCSI device sda: 120103201 512-byte hdwr sectors (61493 MB) Partition check:

 sda: sda1 sda2 sda3

[error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201 ixp425_eth: ixp0 is using the PHY at address 0 ixp425_eth: ixp1 is using the PHY at address 1 ixp425_eth: ixEthMiiLinkStatus failed on PHY0?.

        Can't determine

the auto negotiated parameters. Using default values.

BusyBox? v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands.

  1. Creating ramfs for /var/lock/samba:

Limit the space of log folder: Starting Hostname :

                                                                OK

Starting Modules : Using /lib/modules/pbuttons.o Using /lib/modules/2.4.22-xfs/kernel/drivers/char/x1226-rtc.o X1226: I2C? based RTC driver. i2c-core.o: driver X1226 registered. X1226: found X1226 on IXP425 I2C? Adapter i2c-core.o: client [X1226] registered to adapter [IXP425 I2C? Adapter](pos. 0). atr is 1f enable_irq(22) unbalanced from c38b11bc Using /lib/modules/rbuttons.o Starting Modules : Setting LAN media type : Starting Set CGI_ds.conf: kjournald starting. Commit interval 5 seconds EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal EXT3?-fs: recovery complete. EXT3?-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal EXT3?-fs: recovery complete. EXT3?-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal EXT3?-fs: mounted filesystem with ordered data mode. Setting up swapspace version 0, size = 65007616 bytes Adding Swap: 63484k swap-space (priority -1)

                                                                OK

Restore time and timezone: 09/20/2004-23:04:22

                                                                OK

Restore usrgrpshares:

                                                                OK

Generating telnet password:

                                                                OK

Starting WEB Server:

                                                                OK
                                                                OK

Starting samba: Starting download: download uses obsolete (PF_INET,SOCK_PACKET) ixp425_eth: ixp0: Entering promiscuous mode device ixp0 entered promiscuous mode Starting INET Server:

                                                                OK

Creating ramfs for /tmp: Starting QuickSet? Daemon :

                                                                OK
                                                                OK

Starting Crond : Starting Rest Task : LKG0FB7A9?: boot complete!

                                                                Checking quotas.
 This may take some time.

OK Checking disk status : USB HDD attached EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended EXT3? FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal Done. Turning on quota.

  1. df

Filesystem 1k-blocks Used Available Use% Mounted on rootfs 9911 8919 890 91% / /dev/ram0 9911 8919 890 91% / /dev/sda1 58920100 1103776 57217728 2% /share/hdd/data /dev/sda2 123955 25341 97334 21% /share/hdd/conf

  1. busybox

BusyBox? v0.60.4 (2004.05.28-07:40+0000) multi-call binary

[...]

view · edit · print · history · Last edited by dyoung.
Based on work by dyoung.
Originally by ka6sox.
Page last modified on April 14, 2005, at 10:26 PM