RedBoot> exec 0x01d00000
 Using base address 0x01d00000 and length 0x000be730
 Uncompressing Linux.................................................... done, booting the kernel.
 Linux version 2.4.22-xfs (dereky@localhost) (gcc version 3.4.2) #1 Sun Sep 19 20:44:21 HST 2004
 CPU: XScale-IXP425/IXC1100 revision 1
 Machine: Intel IXDP425 Development Platform
 Warning: bad configuration page, trying to continue
 Security risk: creating user accessible mapping for 0x60000000 at 0xff00f000
 Security risk: creating user accessible mapping for 0x51000000 at 0xf1000000
 On node 0 totalpages: 8192
 zone(0): 8192 pages.
 zone(1): 0 pages.
 zone(2): 0 pages.
 Kernel command line: root=/dev/ram0 initrd=0x01000000,10M mem=32M@0x00000000 console=ttyS0,115200n8
 Calibrating delay loop... 131.48 BogoMIPS
 Memory: 32MB = 32MB total
 Memory: 20420KB available (1235K code, 245K data, 236K init)
 Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
 Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
 Mount cache hash table entries: 512 (order: 0, 4096 bytes)
 Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
 Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
 POSIX conformance testing by UNIFIX
 PCI Autoconfig: Found Bus 0, Device 1, Function 0
 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000
 PCI Autoconfig: Found Bus 0, Device 1, Function 1
 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000
 PCI Autoconfig: Found Bus 0, Device 1, Function 2
 PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00
 PCI: bus0: Fast back to back transfers disabled
 Linux NET4?.0 for Linux 2.4
 Based upon Swansea University Computer Society NET3?.039
 Initializing RT netlink socket
 Starting kswapd
 VFS: Disk quotas vdquot_6.5.1
 Journalled Block Device driver loaded
 i2c-core.o: i2c core module
 i2c-dev.o: i2c /dev entries driver module
 i2c-core.o: driver i2c-dev dummy driver registered.
 i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830)
 pty: 256 Unix98 ptys configured
 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
 ttyS00 at 0xff000003 (irq = 15) is a XScale UART
 ttyS01 at 0xff001003 (irq = 13) is a XScale UART
 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
 SCSI subsystem driver Revision: 1.00
 * host:<NULL>
 cfi_cmdset_0001: Erase suspend on write enabled
 Using buffer write method
 Using static MTD partitions.
 Creating 4 MTD partitions on "IXP425 Flash":
 0x00000000-0x00040000 : "RedBoot "
 0x00040000-0x00060000 : "System Configuration"
 0x00060000-0x00160000 : "Kernel"
 0x00160000-0x00800000 : "Ramdisk"
 usb.c: registered new driver hub
 pci probe begin
 ehci_hcd 00:01.2: NEC Corporation USB 2.0
 ehci_hcd 00:01.2: irq 26, pci mem c3801f00
 usb.c: new USB bus registered, assigned bus number 1
 PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
 PCI: 00:01.2 PCI cache line size corrected to 32.
 ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
 hub.c: USB hub found
 hub.c: 5 ports detected
 pci probe ok
 host/usb-uhci.c: $Revision: 1.1 $ time 20:45:36 Sep 19 2004
 host/usb-uhci.c: High bandwidth mode enabled
 host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
 host/usb-ohci.c: USB OHCI at membase 0xc3809000, IRQ 28
 host/usb-ohci.c: usb-00:01.0, NEC Corporation USB
 usb.c: new USB bus registered, assigned bus number 2
 hub.c: USB hub found
 hub.c: 3 ports detected
 host/usb-ohci.c: USB OHCI at membase 0xc380f000, IRQ 27
 host/usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2)
 usb.c: new USB bus registered, assigned bus number 3
 hub.c: USB hub found
 hub.c: 2 ports detected
 Initializing USB Mass Storage driver...
 usb.c: registered new driver usb-storage
 USB Mass Storage support registered.
 i2c-dev.o: Registered 'IXP425 I2C Adapter' as minor 0
 i2c-core.o: adapter IXP425 I2C Adapter registered as adapter 0.
 NET4: Linux TCP/IP 1.0 for NET4?.0
 IP Protocols: ICMP, UDP, TCP, IGMP
 IP: routing cache hash table of 512 buckets, 4Kbytes
 TCP: Hash tables configured (established 2048 bind 4096)
 IP-Config: No network devices available.
 NET4?: Unix domain sockets 1.0/SMP for Linux NET4.0.
 NetWinder? Floating Point Emulator V0.97 (double precision)
 RAMDISK: Compressed image found at block 0
 Freeing initrd memory: 10240K
 VFS: Mounted root (ext2 filesystem) readonly.
 Freeing init memory: 236K
 Insmod ixp400
 Using /lib/modules/2.4.22-xfs/kernel/drivers/ixp400/ixp400.o
 hub.c: new USB device 00:01.2-1, assigned address 2
 Protocol: Transparent SCSI
 before kernel thread
 Warning: loading ixp400 will taint the kernel: no license
   See http://www.tux.org/lkml/#export-tainted for information about tainted modules
 *** detect:usb-storage
 * scsi_register: usb-storage-1,
 * scsi_reg, hostno:1 prot is 49
 * scsi_reg, retval->host_no:1
 scsi1 : SCSI emulation for USB Mass Storage devices
 ! scan_scsis
 Module init.
 Insmod ixp425
 Using /lib/modules/2.4.22-xfs/kernel/drivers/net/ixp425_eth.o
 do read capacity!!!
 ixp425_eth:
 Initializing IXP425 NPE Ethernet driver software v. 1.1
 ixp425_eth: CPU clock speed (approx) = 0 MHz
  read capacity ok!!!
 The capacity is 120103201
 *** 49
 31 port connect!!!!!=]
   Vendor: Maxtor 4  Model: R060L0            Rev: RAMC
   Type:   Direct-Access                      ANSI SCSI revision: 02
 the host no is 1
 * sd_attach:0
 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
 SCSI device sda: 120103201 512-byte hdwr sectors (61493 MB)
 Partition check:
  sda: sda1 sda2 sda3
 [error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201
 ixp425_eth: ixp0 is using the PHY at address 0
 ixp425_eth: ixp1 is using the PHY at address 1
 ixp425_eth: ixEthMiiLinkStatus failed on PHY0.
         Can't determine
 the auto negotiated parameters. Using default values.  


 [=BusyBox v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash)
 Enter 'help' for a list of built-in commands. 

 # Creating ramfs for /var/lock/samba:
 Limit the space of log folder:
 Starting Hostname :
                                                                OK
 Starting Modules :
 Using /lib/modules/pbuttons.o
 Using /lib/modules/2.4.22-xfs/kernel/drivers/char/x1226-rtc.o
 X1226: I2C? based RTC driver.
 i2c-core.o: driver X1226 registered.
 X1226: found X1226 on IXP425 I2C? Adapter
 i2c-core.o: client [X1226] registered to adapter [IXP425 I2C? Adapter](pos. 0).
 atr is 1f
 enable_irq(22) unbalanced from c38b11bc
 Using /lib/modules/rbuttons.o
 Starting Modules :
 Setting LAN media type :
 Starting Set CGI_ds.conf:
 kjournald starting.  Commit interval 5 seconds
 EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
 EXT3?-fs: recovery complete.
 EXT3?-fs: mounted filesystem with ordered data mode.
 kjournald starting.  Commit interval 5 seconds
 EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
 EXT3?-fs: recovery complete.
 EXT3?-fs: mounted filesystem with ordered data mode.
 kjournald starting.  Commit interval 5 seconds
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
 EXT3?-fs: mounted filesystem with ordered data mode.
 Setting up swapspace version 0, size = 65007616 bytes
 Adding Swap: 63484k swap-space (priority -1)
                                                                OK
 Restore time and timezone:
 09/20/2004-23:04:22
                                                                OK
 Restore usrgrpshares:
                                                                OK
 Generating telnet password:
                                                                OK
 Starting WEB Server:
                                                                OK
                                                                OK
 Starting samba:
 Starting download:
 download uses obsolete (PF_INET,SOCK_PACKET)
 ixp425_eth: ixp0: Entering promiscuous mode
 device ixp0 entered promiscuous mode
 Starting INET Server:
                                                                OK
 Creating ramfs for /tmp:
 Starting QuickSet? Daemon :
                                                                OK
                                                                OK
 Starting Crond :
 Starting Rest Task :
 LKG0FB7A9: boot complete!
                                                                Checking quotas.
  This may take some time.

 OK
 Checking disk status :
 USB HDD attached
 EXT3?-fs warning: maximal mount count reached, running e2fsck is recommended
 EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
 Done.
 Turning on quota. 

 # df
 Filesystem           1k-blocks      Used Available Use% Mounted on
 rootfs                    9911      8919       890  91% /
 /dev/ram0                 9911      8919       890  91% /
 /dev/sda1             58920100   1103776  57217728   2% /share/hdd/data
 /dev/sda2               123955     25341     97334  21% /share/hdd/conf
 # busybox
 BusyBox v0.60.4 (2004.05.28-07:40+0000) multi-call binary

 [...]