Describe BadSlugImageBad here.

 Restarting system.        
 +Ethernet eth0: MAC address 00:04:5a:0f:b0:7f
 IP: 192.168.0.1/255.255.255.0, Gateway: 192.168.0.1
 Default server: 0.0.0.0, DNS server IP: 0.0.0.0

 RedBoot(tm) bootstrap and debug environment [ROMRAM]
 Red Hat certified release, version 1.92 - built 15:16:07, Feb  3 2004

 Platform: IXDP425? Development Platform (XScale?) 
 Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

 RAM: 0x00000000-0x02000000, 0x000723a0-0x01ff3000 available
 FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
 == Executing boot script in 2.000 seconds - enter ^C to abort
 ^C
 RedBoot> ip_address -l 192.168.0.78 -h 192.168.0.10
 IP: 192.168.0.78/255.255.255.0, Gateway: 192.168.0.1
 Default server: 192.168.0.10, DNS server IP: 0.0.0.0
 RedBoot> load -r -v -b 0x01000000 /nslu2/test0.bin
 Using default protocol (TFTP)
 /
 Raw file loaded 0x01000000-0x017fffff, assumed entry at 0x01000000
 RedBoot> cksum
 Computing cksum for area 0x01000000-0x01800000
 POSIX cksum = 4012176918 8388608 (0xef24f616 0x00800000)
 RedBoot> fis write -f 0x50060000 -b 0x01060000 -l 0x7a0000
 * CAUTION * about to program FLASH
             at 0x50060000..0x507fffff from 0x01060000 - continue (y/n)? y
 ... Erase from 0x50060000-0x50800000: ..........................................
 ...................
 RedBoot> reset
 ... Resetting.+Ethernet eth0: MAC address 00:04:5a:0f:b0:7f
 IP: 192.168.0.1/255.255.255.0, Gateway: 192.168.0.1
 Default server: 0.0.0.0, DNS server IP: 0.0.0.0

 RedBoot(tm) bootstrap and debug environment [ROMRAM]
 Red Hat certified release, version 1.92 - built 15:16:07, Feb  3 2004

 Platform: IXDP425? Development Platform (XScale?) 
 Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

 RAM: 0x00000000-0x02000000, 0x000723a0-0x01ff3000 available
 FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
 == Executing boot script in 2.000 seconds - enter ^C to abort
 RedBoot> boot;exec 0x01d00000
 have eRcOmM 
 copy kernel code from flash to RAM
 copy ramdisk file from flash to RAM
 run kernel 
 Using base address 0x01d00000 and length 0x000c4258
 Uncompressing Linux...................................................... done, 
 booting the kernel.
 Linux version 2.4.22-xfs (fontenot@quasar) (gcc version 3.4.2) #1 Thu Nov 11 08:
 10:38 PST 2004
 CPU: XScale?-IXP425/IXC1100? revision 1
 Machine: Intel IXDP425? Development Platform
 Warning: bad configuration page, trying to continue
 Security risk: creating user accessible mapping for 0x60000000 at 0xff00f000
 Security risk: creating user accessible mapping for 0x51000000 at 0xf1000000
 On node 0 totalpages: 8192                                                  
 zone(0): 8192 pages.      
 zone(1): 0 pages.   
 zone(2): 0 pages.
 Kernel command line: console=ttyS0,115200n8 root=/dev/slug initrd=0x01000000,10M
  mem=32M@0x00000000
 Calibrating delay loop... 131.48 BogoMIPS?
 Memory: 32MB = 32MB total                
 Memory: 20380KB available (1273K code, 244K data, 240K init)
 Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
 Inode cache hash table entries: 2048 (order: 2, 16384 bytes) 
 Mount cache hash table entries: 512 (order: 0, 4096 bytes)  
 Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
 Page-cache hash table entries: 8192 (order: 3, 32768 bytes) 
 POSIX conformance testing by UNIFIX                        
 PCI Autoconfig: Found Bus 0, Device 1, Function 0
 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000
 PCI Autoconfig: Found Bus 0, Device 1, Function 1          
 PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000
 PCI Autoconfig: Found Bus 0, Device 1, Function 2          
 PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00
 PCI: bus0: Fast back to back transfers disabled           
 Linux NET4?.0 for Linux 2.4                     
 Based upon Swansea University Computer Society NET3?.039
 Initializing RT netlink socket                         
 Starting kswapd               
 VFS: Disk quotas vdquot_6.5.1
 Journalled Block Device driver loaded
 devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
 devfs: boot_options: 0x0                                     
 i2c-core.o: i2c core module
 i2c-dev.o: i2c /dev entries driver module
 i2c-core.o: driver i2c-dev dummy driver registered.
 i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830)
 pty: 256 Unix98 ptys configured                                  
 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en
 abled
 ttyS00 at 0xff000003 (irq = 15) is a XScale? UART
 ttyS01 at 0xff001003 (irq = 13) is a XScale? UART
 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
 SCSI subsystem driver Revision: 1.00                                  
 * host:<NULL>                       
 cfi_cmdset_0001: Erase suspend on write enabled
 Using buffer write method                      
 Creating 17 MTD partitions on "IXP425 Flash":
 0x00000000-0x00800000 : ""                   
 0x00000000-0x00800000 : ""
 0x00000000-0x00800000 : ""
 0x00000000-0x00800000 : ""
 0x00000000-0x00800000 : ""
 0x00000000-0x00800000 : ""
 0x00000000-0x00800000 : ""
 0x00000000-0x00800000 : ""
 0x00000000-0x00800000 : ""
 0x00000000-0x00040000 : "RedBoot"
 0x00040000-0x00060000 : "SysConf?"
 0x00060000-0x00124258 : "Kernel" 
 mtd: partition "Kernel" doesn't end on an erase block -- force read-only
 0x00124258-0x00160000 : "unallocated space"                             
 mtd: partition "unallocated space" doesn't start on an erase block boundary -- f
 orce read-only
 0x00160000-0x004d815d : "Ramdisk"
 mtd: partition "Ramdisk" doesn't end on an erase block -- force read-only
 0x004e0000-0x005e0000 : "Rootdisk"                                       
 0x005e0000-0x007e0000 : "Userdisk"
 0x007e0000-0x00800000 : "FIS directory"
 usb.c: registered new driver usbdevfs  
 usb.c: registered new driver hub     
 pci probe begin                 
 ehci_hcd 00:01.2: NEC Corporation USB 2.0
 ehci_hcd 00:01.2: irq 26, pci mem c3801f00
 usb.c: new USB bus registered, assigned bus number 1
 PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
 PCI: 00:01.2 PCI cache line size corrected to 32.                     
 ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
 hub.c: USB hub found                                                
 hub.c: 5 ports detected
 pci probe ok           
 host/usb-uhci.c: $Revision: 1.1 $ time 08:11:19 Nov 11 2004
 host/usb-uhci.c: High bandwidth mode enabled               
 host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
 host/usb-ohci.c: USB OHCI at membase 0xc3809000, IRQ 28               
 host/usb-ohci.c: usb-00:01.0, NEC Corporation USB      
 usb.c: new USB bus registered, assigned bus number 2
 hub.c: USB hub found                                
 hub.c: 3 ports detected
 host/usb-ohci.c: USB OHCI at membase 0xc380f000, IRQ 27
 host/usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2) 
 usb.c: new USB bus registered, assigned bus number 3  
 hub.c: USB hub found                                
 hub.c: 2 ports detected
 Initializing USB Mass Storage driver...
 usb.c: registered new driver usb-storage
 USB Mass Storage support registered.    
 i2c-dev.o: Registered 'IXP425 I2C? Adapter' as minor 0
 i2c-core.o: adapter IXP425 I2C? Adapter registered as adapter 0.
 NET4?: Linux TCP/IP 1.0 for NET4?.0                              
 IP Protocols: ICMP, UDP, TCP, IGMP
 IP: routing cache hash table of 512 buckets, 4Kbytes
 TCP: Hash tables configured (established 2048 bind 4096)
 IP-Config: No network devices available.                
 NET4?: Unix domain sockets 1.0/SMP for Linux NET4?.0.
 NetWinder? Floating Point Emulator V0.97 (double precision)
 RAMDISK: Compressed image found at block 0                
 Freeing initrd memory: 10240K             
 VFS: Mounted root (ext2 filesystem).
 Firmware Version: V2.3R25-uNSLUng-able-2.14-beta
 mount: Mounting /dev/sda2 on /mnt/tmpmnt failed: No such device or address
 mount: Mounting /dev/sdb2 on /mnt/tmpmnt failed: No such device or address
 Root filesystem will be mounted from /dev/ram0 ...
 Freeing init memory: 240K
 Insmod ixp400            
 Using /lib/modules/2.4.22-xfs/kernel/drivers/ixp400/ixp400.o
 Warning: loading ixp400 will taint the kernel: no license
   See http://www.tux.org/lkml/#export-tainted for information about tainted modu
 les
 Module init.
 Insmod ixp425
 Using /lib/modules/2.4.22-xfs/kernel/drivers/net/ixp425_eth.o
 ixp425_eth: 
 Initializing IXP425 NPE Ethernet driver software v. 1.1 
 ixp425_eth: CPU clock speed (approx) = 0 MHz?            
 [error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201
 ixp425_eth: ixp0 is using the PHY at address 0          
 ixp425_eth: ixp1 is using the PHY at address 1
 ixp425_eth: ixEthMiiLinkStatus failed on PHY0?.
         Can't determine                       
 the auto negotiated parameters. Using default values.


 BusyBox? v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash)
 Enter 'help' for a list of built-in commands.

 # Creating ramfs for /var/lock/samba:
 Limit the space of log folder:
 Starting Hostname :
 OK
 Starting Modules :
 Using /lib/modules/pbuttons.o
 Using /lib/modules/2.4.22-xfs/kernel/drivers/char/x1226-rtc.o
 X1226: I2C? based RTC driver.
 i2c-core.o: driver X1226 registered.
 X1226: found X1226 on IXP425 I2C? Adapter
 i2c-core.o: client [X1226] registered to adapter [IXP425 I2C? Adapter](pos. 0).
 atr is 0                                                                      
 enable_irq(22) unbalanced from c58b51bc
 Using /lib/modules/rbuttons.o          
 Starting Modules :
 Setting LAN media type :
 Starting Set CGI_ds.conf:
 OK
 Restore time and timezone:
 11/12/2004-15:46:57 
 OK
 Restore usrgrpshares:
 OK
 Generating telnet password:
 OK
 Starting WEB Server:
 OK
 OK
 Starting samba:
 Starting download:
 download uses obsolete (PF_INET,SOCK_PACKET)
 ixp425_eth: ixp0: Entering promiscuous mode 
 device ixp0 entered promiscuous mode       
 Starting INET Server:               
 OK
 Creating ramfs for /tmp:
 Starting QuickSet? Daemon :
 OK
 OK
 Starting Crond :
 Starting Rest Task :
 LKG0FB07F?: boot complete!
 Checking quotas. This may take some time.

 OK
 Done.
 Starting UNSLUNG Packages:
 Turning on quota.
 Checking disk status :
 cat /proc/mtd
 dev:    size   erasesize  name
 mtd0: 00800000 00020000 ""
 mtd1: 00800000 00020000 ""
 mtd2: 00800000 00020000 ""
 mtd3: 00800000 00020000 ""
 mtd4: 00800000 00020000 ""
 mtd5: 00800000 00020000 ""
 mtd6: 00800000 00020000 ""
 mtd7: 00800000 00020000 ""
 mtd8: 00800000 00020000 ""
 mtd9: 00040000 00020000 "RedBoot"
 mtd10: 00020000 00020000 "SysConf?"
 mtd11: 000c4258 00020000 "Kernel"
 mtd12: 0003bda8 00020000 "unallocated space"
 mtd13: 0037815d 00020000 "Ramdisk"
 mtd14: 00100000 00020000 "Rootdisk"
 mtd15: 00200000 00020000 "Userdisk"
 # reboot

 The system is going down NOW !!
 Sending SIGTERM to all processes.
 Sending SIGKILL to all processes.


 BusyBox? v0.60.4 (2004.07.01-03:05+0000) Built-in shell (ash)
 Enter 'help' for a list of built-in commands.

 # Enabling flash read mode
 Restarting system.