NSLU2-Linux
view · edit · print · history

MSSII.Bootlog History

Hide minor edits - Show changes to markup

October 04, 2007, at 09:21 PM by BrianZhou -- new bootlog
Changed lines 308-597 from:

to:

optware kernel-image


         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: RD-88F5182-NAS-MXO LE 

U-Boot 1.1.1 (Jun 22 2006 - 15:24:29) Marvell version: MSS2_1.7.301 Maxtor v1.07

DRAM CS[0] base 0x00000000   size  32MB 
DRAM Total size  32MB 
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 500Mhz 
SysClock = 166Mhz , TClock = 166Mhz 


USB 0: host mode
USB 1: host mode
Gpp: Front button is NOT pressed
Gpp: Reset button is NOT pressed
Single drive system detected
Net:   egiga0 [PRIME]
Testing memory from 0x400000 to 0xc00000 len 8388608
Memory test (0x55 pattern)... Pass
Memory test (0xAA pattern)... Pass
Memory test (0x55 pattern)... Pass
Burning Maxtor Params at 0xfffff000 sector 63

.
RD_MAXTOR defined
RD_88F5182 defined
MXO_SATA2 is NOT defined

Marvell Serial ATA Adapter
Intergrated Sata device found
  Device 0: OK
Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)

IDE device 0: Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
Booting in normal mode
Hit any key to stop autoboot:  0 Starting watchdog


Reset IDE: 
Marvell Serial ATA Adapter
Intergrated Sata device found
  Device 0: OK
Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)


Reset IDE: 
Marvell Serial ATA Adapter
Intergrated Sata device found
  Device 0: OK
Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)

Using device ide0, partition 2

Loading from block device ide device 0, partition 2: Name: hda2
  Type: U-Boot  File:/boot/uImage

1437168 bytes read
## Booting image at 00200000 ...
   Image Name:   Linux-2.6.12.6-arm1
   Created:      2007-10-04  20:56:46 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1437104 Bytes =  1.4 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................... done, booting the kernel.
Linux version 2.6.12.6-arm1 (slug@otto) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #1 Thu Oct 4 20:56:43 UTC 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets

]@Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 166666667, Tclk = 166666667
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw
PID hash table entries: 256 (order: 8, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB 0MB 0MB 0MB = 32MB total
Memory: 29360KB available (2488K code, 393K data, 100K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

  Marvell Development Board (LSP Version 1.7.801_NAS_MAXTOR)-- RD-88F5182-NAS-MXO 

 Detected Tclk 166666667 and SysClk 166666667 
Marvell USB EHCI Host controller #0: c037fb00
Marvell USB EHCI Host controller #1: c037fa40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initialize buttons dev...done 
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3 
Done. 
cesadev_init(c000eed0)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Intel(R) PRO/1000 Network Driver - version 6.0.54-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface 'egiga0' 
e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: Seagate   Model: ST3320620AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
physmap flash device: 40000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.<6>NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 100K
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS on sda5, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Found Orion-Nas XML configuration file.
Configuring LAN interface... egiga0: link down
done
Configuring Disks... done
Starting swap... Adding 257032k swap on /dev/sda3.  Priority:-1 extents:1
done
Mounting Partitions... kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
done
Starting webGUI... done
Starting cups... egiga0: link up<5>, full duplex<5>, speed 100 Mbps<5>
done
Starting Samba... done
Starting udev... done
Starting syncaway... done
Starting btnsd... done

===============================
 Starting MXO Initialization.. 
===============================

Setting current_boot_partition value.. done
Starting network monitor daemon.. done
Starting discoverd.. done
Starting hnscontrol.. done
Starting bonjour.. done
Starting watchdog daemon.. done
Starting crond[449]: crond 2.3.2 dillon, started, log level 0

done
Creating Configuration html.. done
tune2fs 1.38 (30-Jun-2005)
Setting reserved blocks percentage to 1 (778228 blocks)

Maxtor MSSII firmware version : 3.1.28



*** Marvell Semiconductors ltd.
    This is MSS-NAS version: 1009p_1 running on EE1-1HDD platform
    built on: Thu Jun 15 23:17:13 UTC 2006

    LAN IP address: 192.168.1.55 (static)

    Port configuration:

    LAN   -> egiga0
Starting Optware.


BusyBox v1.01 (2006.03.03-02:59+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ #
October 02, 2007, at 03:09 AM by BrianZhou -- added bootlog of stock firmware
Changed lines 1-2 from:

Stock firmware

to:

Stock firmware

Changed lines 306-308 from:

@]

to:

@]


October 02, 2007, at 03:07 AM by BrianZhou -- added bootlog of stock firmware
Added lines 1-305:

Stock firmware

# picocom -b 115200 /dev/ttyUSB0
picocom v1.4

port is        : /dev/ttyUSB0
flowcontrol    : none
baudrate is    : 115200
parity is      : none
databits are   : 8
escape is      : C-a
noinit is      : no
noreset is     : no
nolock is      : no
send_cmd is    : ascii_xfr -s -v -l10
receive_cmd is : rz -vv

Terminal ready

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: RD-88F5182-NAS-MXO LE

U-Boot 1.1.1 (Jun 22 2006 - 15:24:29) Marvell version: MSS2_1.7.301 Maxtor v1.07

DRAM CS[0] base 0x00000000   size  32MB
DRAM Total size  32MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz


USB 0: host mode
USB 1: host mode
Gpp: Front button is NOT pressed
Gpp: Reset button is NOT pressed
Waiting for front button press
Single drive system detected
Net:   egiga0 [PRIME]
Testing memory from 0x400000 to 0xc00000 len 8388608
Memory test (0x55 pattern)... Pass
Memory test (0xAA pattern)... Pass
Memory test (0x55 pattern)... Pass
Burning Maxtor Params at 0xfffff000 sector 63

.
RD_MAXTOR defined
RD_88F5182 defined
MXO_SATA2 is NOT defined

Marvell Serial ATA Adapter
Intergrated Sata device found
  Device 0: OK
Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)


IDE device 0: Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
Booting in normal mode
Hit any key to stop autoboot:  0 Starting watchdog


Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
  Device 0: OK
Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)


Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
  Device 0: OK
Model: ST3320620AS                            Firm: 3.AAD    Ser#:             3QF0WE6Q
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)

Using device ide0, partition 2

Loading from block device ide device 0, partition 2: Name: hda2
  Type: U-Boot  File:/boot/uImage

1593744 bytes read
## Booting image at 00200000 ...
   Image Name:   Linux-2.6.12.6-arm1
   Created:      2006-08-22  22:55:28 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1593680 Bytes =  1.5 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux........................................................................................................ done, booting the kernel.
Linux version 2.6.12.6-arm1 (root@bigcent) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #1 Tue Aug 22 15:55:07 PDT 2006
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 166666667, Tclk = 166666667
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw
PID hash table entries: 256 (order: 8, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB 0MB 0MB 0MB = 32MB total
Memory: 29056KB available (2775K code, 468K data, 104K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

  Marvell Development Board (LSP Version 1.7.801_NAS_MAXTOR)-- RD-88F5182-NAS-MXO

 Detected Tclk 166666667 and SysClk 166666667
Marvell USB EHCI Host controller #0: c03dab00
Marvell USB EHCI Host controller #1: c03daa40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initialize buttons dev...done
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done. 
cesadev_init(c000ef90)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.22 [Flags: R/O].
Initializing Cryptographic API 
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered 
io scheduler deadline registered
io scheduler cfq registered
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled 
  o Loading network interface 'egiga0'  
STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
Linux video capture interface: v1.00
V4L-Driver for Vision CPiA based cameras v1.2.3
Since in-kernel colorspace conversion is not allowed, it is disabled by default now. Users should fix the applications in case they don't work without conversion reenabled by setting the 'colorspace_conv' module parameter to 1<6>USB driver for Vision CPiA based cameras v1.2.3
usbcore: registered new driver cpia
radio-maestro: no devices found.
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter 
scsi1 : Marvell SCSI to SATA adapter
  Vendor: Seagate   Model: ST3320620AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
NFTL driver: nftlcore.c $Revision: 1.97 $, nftlmount.c $Revision: 1.40 $
physmap flash device: 40000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
ftl_cs: FTL header not found.
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 104K
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: checktime reached, running e2fsck is recommended
EXT3 FS on sda5, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Found Orion-Nas XML configuration file.
Configuring LAN interface... egiga0: link down
done
Configuring Disks... done
Starting swap... Adding 257032k swap on /dev/sda3.  Priority:-1 extents:1
done
Mounting Partitions... kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
done
Starting webGUI... done
Starting cups... egiga0: link up<5>, full duplex<5>, speed 100 Mbps<5>
done
Starting Samba... done
Starting udev... done
Starting syncaway... done
Starting btnsd... done

===============================
 Starting MXO Initialization.. 
===============================

Setting wait for button press on.. done
Setting current_boot_partition value.. done
Starting network monitor daemon.. done
Starting discoverd.. done
Starting hnscontrol.. done
Starting bonjour.. done
Starting watchdog daemon.. done
Starting crond[462]: crond 2.3.2 dillon, started, log level 0

done
Creating Configuration html.. done
tune2fs 1.38 (30-Jun-2005)
Setting reserved blocks percentage to 1 (778228 blocks)

Maxtor MSSII firmware version : 3.1.28



*** Marvell Semiconductors ltd.
    This is MSS-NAS version: 1009p_1 running on EE1-1HDD platform
    built on: Thu Jun 15 23:17:13 UTC 2006

    LAN IP address: 192.168.1.55 (static)

    Port configuration:

    LAN   -> egiga0

BusyBox v1.01 (2006.03.03-02:59+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

view · edit · print · history · Last edited by BrianZhou.
Originally by BrianZhou.
Page last modified on October 04, 2007, at 09:21 PM