PPCBoot? 2.0.0 (Mar 1 2005 - 15:31:41)

CPU: MPC8245? Revision 1.4 at 266.666 MHz?: 16 kB I-Cache 16 kB D-Cache Board: Sandpoint 8245 Unity ##Test not implemented yet## I2C?: ready DRAM: DRAM BANK = 1 MAX_DRAM_SIZE = 4000000 MCCR1? = 75a80002 MCCR4? = 35363331 MSAR1? = 0 EMSAR1? = 0 MEAR1? = 3f EMEAR1? = 0 MSAR2? = 0 EMSAR2? = 0 MEAR2? = 0 EMEAR2? = 0 MBER = 32000001 64 MB addr_sp=3f1ff78, id=3f1ff98, addr=3fc0000 FLASH: 16 MB

• Warning - bad CRC, using default environment

In: serial Out: serial Err: serial Net: No ethernet found. Press space to abort autoboot in 1 second

1. Booting image at ff000000 ... Image Name: kernel Image Type: PowerPC? Linux Kernel Image (gzip compressed) Data Size: 1142483 Bytes = 1.1 MB Load Address: 00000000 Entry Point: 0000000c Verifying Checksum ... OK Uncompressing Kernel Image ... OK
2. Loading RAMDisk? Image at ff180000 ... Image Name: ramdisk Image Type: PowerPC? Linux RAMDisk? Image (gzip compressed) Data Size: 6202278 Bytes = 5.9 MB Load Address: 00000000 Entry Point: 0000000c Verifying Checksum ... OK Loading Ramdisk to 03934000, end 03f1e3a6 ... OK

Memory BAT mapping: BAT2?=64Mb, BAT3?=0Mb, residual: 0Mb

(:table border=0 width=100% bgcolor=#eeeeff:) (:cell:)

 
Linux version 2.4.22-uc0 (???@???)  (gcc version 3.4) 3.4) #1 Thu Jun 2 15:31:41 CST 2005
Motorola  PMC8241
PORTING  by  Premier Microelectronics Development
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,115200 root=/dev/hda4
rw ip=off initrd=0x00800000,16M mem=64M@0x00000000 hda=bswap
ide_setup: hda=bswap
OpenPIC Version 1.2 (1 CPUs and 138 IRQ sources) at fc040000
Decrementer frequency = 133.333377 MHz
Warning: real time clock seems stuck!
Calibrating delay loop... 177.35 BogoMIPS
Memory: 56028k available (1864k kernel code, 740k data, 72k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 0, pin = 1, irq = 0
sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 13, pin = 1, irq = 16
sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 14, pin = 1, irq = 17
sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 14, pin = 2, irq = 17
sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 14, pin = 3, irq = 17
sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 15, pin = 1, irq = 18
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xfc004500 (irq = 137) is a ST16650
ttyS01 at 0xfc004600 (irq = 138) is a ST16650
Generic RTC Driver v1.07
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
physmap flash device: 1000000 at ff000000
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
master->size = 1000000, erasesize = 20000
No RedBoot partition table detected in Physically mapped flash
physmap: no partition info available, registering whole flash at once
Creating 8 MTD partitions on "Physically mapped flash":
0x00f00000-0x00f40000 : "ppcboot"
0x00000000-0x00180000 : "zImage"
0x00180000-0x00800000 : "rd.gz"
0x00800000-0x00f00000 : "AllLib.tgz"
0x00f80000-0x00fa0000 : "vendor"
Mac0 00:11:32:00:56:00
vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
Vender partition MacNum:1 retlen:64
0x00fa0000-0x00fc0000 : "synocfg"
0x00fc0000-0x00fe0000 : "RedBoot Config"
0x00fe0000-0x01000000 : "FIS directory"
PPP generic driver version 2.4.2
PPP MPPE compression module registered
PPP Deflate Compression module registered
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SiI3512 Serial ATA: IDE controller at PCI slot 00:0d.0
SiI3512 Serial ATA: chipset revision 1
SiI3512 Serial ATA: not 100% native mode: will probe irqs later
ide0: MMIO-DMA at 0xc5000e00-0xc5000e07, BIOS settings: hda:pio, hdb:pio
ide1: MMIO-DMA at 0xc5000e08-0xc5000e0f, BIOS settings: hdc:pio, hdd:pio
ide0: reset phy, status=0x00000113, siimage_reset
Probing IDE interface ide0...
hda: SAMSUNG SP2004C, ATA DISK drive
blk: queue c0296230, I/O limit 4095Mb (mask 0xffffffff)
ide1: reset phy, status=0x00000000, siimage_reset
ide1: reset phy dead, status=0x00000000
siimage_reset: no drive on ide1.
Probing IDE interface ide1...
ide0 at 0xc5000e80-0xc5000e87,0xc5000e8a on irq 16
ide1 at 0xc5000ec0-0xc5000ec7,0xc5000eca on irq 16
ide2: DISABLED, NO IRQ
ide3: DISABLED, NO IRQ
ide4: DISABLED, NO IRQ
ide5: DISABLED, NO IRQ
ide6: DISABLED, NO IRQ
ide7: DISABLED, NO IRQ
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 390721968 sectors (200050 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(133)
Partition check:
hda: hda1 hda2 hda3 hda4
SCSI subsystem driver Revision: 1.00
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:0e.2: NEC Corporation USB 2.0
ehci_hcd 00:0e.2: irq 17, pci mem c5002f00
usb.c: new USB bus registered, assigned bus number 1
PCI: 00:0e.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:0e.2 PCI cache line size corrected to 32.
ehci_hcd 00:0e.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 5 ports detected
host/usb-uhci.c: $Revision: 1.5 $ time 15:32:45 Jun  2 2005
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
host/usb-ohci.c: USB OHCI at membase 0xc5004000, IRQ 17
host/usb-ohci.c: usb-00:0e.0, NEC Corporation USB
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
host/usb-ohci.c: USB OHCI at membase 0xc5006000, IRQ 17
host/usb-ohci.c: usb-00:0e.1, NEC Corporation USB (#2)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usblp
printer.c: v0.11: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: AppleTalk 0.18a for Linux NET4.0
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 6056k freed
VFS: Mounted root (ext2 filesystem).
reiserfs: found format "3.6" with standard journal
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,1)) ...
for (ide0(3,1))
reiserfs: replayed 5 transactions in 0 seconds
ide0(3,1):Using r5 hash to sort names
reiserfs: found format "3.6" with standard journal
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,4)) ...
for (ide0(3,4))
ide0(3,4):Using r5 hash to sort names
FAT: check NTFS format (test 1)
FAT: check NTFS format (test 2)
FAT: bogus logical sector size 0
reiserfs: found format "3.6" with standard journal
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,4)) ...
for (ide0(3,4))
ide0(3,4):Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem).
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 72k init
reiserfs: found format "3.6" with standard journal
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,1)) ...
for (ide0(3,1))
ide0(3,1):Using r5 hash to sort names
Adding Swap: 393584k swap-space (priority -1)
sk98lin: Network Device Driver v7.04
(C)Copyright 1999-2004 Marvell(R).
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A  RlmtMode:Check Link State
Got EUMBBAR 0xfc000000
synobios.c(mpc_i2c_init)(1954) i2c_base = fc003000
synobios.c(1876)target = 32
I2C read 0x20
I2C read 0x39
I2C read 0x31
I2C read 0x0
I2C read 0x28
I2C read 0x8
I2C read 0x5
synobios: load, major number 201
reiserfs: found format "3.6" with standard journal
eth0: network connection up using port A
speed:           1000
autonegotiation: yes
duplex mode:     full
flowctrl:        symmetric
role:            slave
irq moderation:  disabled
scatter-gather:  disabled
reiserfs: using ordered data mode
reiserfs: checking transaction log (device ide0(3,3)) ...
for (ide0(3,3))
reiserfs: replayed 3 transactions in 0 seconds
ide0(3,3):Using r5 hash to sort names

(:tableend:)

 Motorola  PMC8241

 OpenPIC Version 1.2 (1 CPUs and 138 IRQ sources) at fc040000
 Decrementer frequency = 133.333377 MHz

 Calibrating delay loop... 177.35 BogoMIPS

 Linux NET4.0 for Linux 2.4
 Based upon Swansea University Computer Society NET3.039

 ttyS00 at 0xfc004500 (irq = 137) is a ST16650
 ttyS01 at 0xfc004600 (irq = 138) is a ST16650

 0x00800000-0x00f00000 : "AllLib.tgz"

 Vender partition MacNum:1 retlen:64

 SiI3512 Serial ATA: IDE controller at PCI slot 00:0d.0
 SiI3512 Serial ATA: chipset revision 1
 SiI3512 Serial ATA: not 100% native mode: will probe irqs later

 hda: SAMSUNG SP2004C, ATA DISK drive

 NET4: Linux TCP/IP 1.0 for NET4.0

 NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
 NET4: AppleTalk 0.18a for Linux NET4.0

 PrefPort:A  RlmtMode:Check Link State

 I2C read 0x20
 I2C read 0x39
 I2C read 0x31
 I2C read 0x0
 I2C read 0x28
 I2C read 0x8
 I2C read 0x5

 3.4) #1 Thu Jun 2 15:31:41 CST 2005
 Motorola  PMC8241?
 PORTING  by  Premier Microelectronics Development
 On node 0 totalpages: 16384
 zone(0): 16384 pages.
 zone(1): 0 pages.
 zone(2): 0 pages.
 Kernel command line: console=ttyS0,115200 root=/dev/hda4 rw ip=off initrd=0x00800000,16M mem=64M@0x00000000 hda=bswap
 ide_setup: hda=bswap
 OpenPIC? Version 1.2 (1 CPUs? and 138 IRQ sources) at fc040000
 Decrementer frequency = 133.333377 MHz?
 Warning: real time clock seems stuck!
 Calibrating delay loop... 177.35 BogoMIPS?
 Memory: 56028k available (1864k kernel code, 740k data, 72k init, 0k highmem)
 Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
 Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
 Mount cache hash table entries: 512 (order: 0, 4096 bytes)
 Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
 Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
 POSIX conformance testing by UNIFIX
 PCI: Probing PCI hardware
 sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 0, pin = 1, irq = 0
 sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 13, pin = 1, irq = 16
 sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 14, pin = 1, irq = 17
 sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 14, pin = 2, irq = 17
 sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 14, pin = 3, irq = 17
 sandpoint_pci.c(sandpoint_map_irq)(71) idsel = 15, pin = 1, irq = 18
 Linux NET4?.0 for Linux 2.4
 Based upon Swansea University Computer Society NET3?.039
 Initializing RT netlink socket
 Starting kswapd
 kinoded started
 VFS: Disk quotas vdquot_6.5.1
 Journalled Block Device driver loaded
 pty: 256 Unix98 ptys configured
 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
 ttyS00 at 0xfc004500 (irq = 137) is a ST16650?
 ttyS01 at 0xfc004600 (irq = 138) is a ST16650?
 Generic RTC Driver v1.07
 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
 physmap flash device: 1000000 at ff000000
 Amd/Fujitsu Extended Query Table v1.3 at 0x0040
 number of CFI chips: 1
 cfi_cmdset_0002: Disabling fast programming due to code brokenness.
 master->size = 1000000, erasesize = 20000
 No RedBoot partition table detected in Physically mapped flash
 physmap: no partition info available, registering whole flash at once
 Creating 8 MTD partitions on "Physically mapped flash":
 0x00f00000-0x00f40000 : "ppcboot"
 0x00000000-0x00180000 : "zImage"
 0x00180000-0x00800000 : "rd.gz"
 0x00800000-0x00f00000 : "AllLib?.tgz"
 0x00f80000-0x00fa0000 : "vendor"
 Mac0 00:11:32:00:56:00
 vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
 Vender partition MacNum?:1 retlen:64
 0x00fa0000-0x00fc0000 : "synocfg"
 0x00fc0000-0x00fe0000 : "RedBoot Config"
 0x00fe0000-0x01000000 : "FIS directory"
 PPP generic driver version 2.4.2
 PPP MPPE compression module registered
 PPP Deflate Compression module registered
 Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
 SiI3512? Serial ATA: IDE controller at PCI slot 00:0d.0
 SiI3512? Serial ATA: chipset revision 1
 SiI3512? Serial ATA: not 100% native mode: will probe irqs later
 ide0: MMIO-DMA at 0xc5000e00-0xc5000e07, BIOS settings: hda:pio, hdb:pio
 ide1: MMIO-DMA at 0xc5000e08-0xc5000e0f, BIOS settings: hdc:pio, hdd:pio
 ide0: reset phy, status=0x00000113, siimage_reset
 Probing IDE interface ide0...
 hda: SAMSUNG SP2004C?, ATA DISK drive
 blk: queue c0296230, I/O limit 4095Mb (mask 0xffffffff)
 ide1: reset phy, status=0x00000000, siimage_reset
 ide1: reset phy dead, status=0x00000000
 siimage_reset: no drive on ide1.
 Probing IDE interface ide1...
 ide0 at 0xc5000e80-0xc5000e87,0xc5000e8a on irq 16
 ide1 at 0xc5000ec0-0xc5000ec7,0xc5000eca on irq 16
 ide2: DISABLED, NO IRQ
 ide3: DISABLED, NO IRQ
 ide4: DISABLED, NO IRQ
 ide5: DISABLED, NO IRQ
 ide6: DISABLED, NO IRQ
 ide7: DISABLED, NO IRQ
 hda: attached ide-disk driver.
 hda: host protected area => 1
 hda: 390721968 sectors (200050 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(133)
 Partition check:
 hda: hda1 hda2 hda3 hda4
 SCSI subsystem driver Revision: 1.00
 usb.c: registered new driver usbdevfs
 usb.c: registered new driver hub
 ehci_hcd 00:0e.2: NEC Corporation USB 2.0
 ehci_hcd 00:0e.2: irq 17, pci mem c5002f00
 usb.c: new USB bus registered, assigned bus number 1
 PCI: 00:0e.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
 PCI: 00:0e.2 PCI cache line size corrected to 32.
 ehci_hcd 00:0e.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
 hub.c: USB hub found
 hub.c: 5 ports detected
 host/usb-uhci.c: $Revision: 1.5 $ time 15:32:45 Jun  2 2005
 host/usb-uhci.c: High bandwidth mode enabled
 host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
 host/usb-ohci.c: USB OHCI at membase 0xc5004000, IRQ 17
 host/usb-ohci.c: usb-00:0e.0, NEC Corporation USB
 usb.c: new USB bus registered, assigned bus number 2
 hub.c: USB hub found
 hub.c: 3 ports detected
 host/usb-ohci.c: USB OHCI at membase 0xc5006000, IRQ 17
 host/usb-ohci.c: usb-00:0e.1, NEC Corporation USB (#2)
 usb.c: new USB bus registered, assigned bus number 3
 hub.c: USB hub found
 hub.c: 2 ports detected
 usb.c: registered new driver usblp
 printer.c: v0.11: USB Printer Device Class driver
 Initializing USB Mass Storage driver...
 usb.c: registered new driver usb-storage
 USB Mass Storage support registered.
 NET4?: Linux TCP/IP 1.0 for NET4?.0
 IP Protocols: ICMP, UDP, TCP
 IP: routing cache hash table of 512 buckets, 4Kbytes
 TCP: Hash tables configured (established 4096 bind 8192)
 NET4?: Unix domain sockets 1.0/SMP for Linux NET4?.0.
 NET4?: AppleTalk? 0.18a for Linux NET4?.0
 RAMDISK: Compressed image found at block 0
 Freeing initrd memory: 6056k freed
 VFS: Mounted root (ext2 filesystem).
 reiserfs: found format "3.6" with standard journal
 reiserfs: using ordered data mode
 reiserfs: checking transaction log (device ide0(3,1)) ...
 for (ide0(3,1))
 reiserfs: replayed 5 transactions in 0 seconds
 ide0(3,1):Using r5 hash to sort names
 reiserfs: found format "3.6" with standard journal
 reiserfs: using ordered data mode
 reiserfs: checking transaction log (device ide0(3,4)) ...
 for (ide0(3,4))
 ide0(3,4):Using r5 hash to sort names
 FAT: check NTFS format (test 1)
 FAT: check NTFS format (test 2)
 FAT: bogus logical sector size 0
 reiserfs: found format "3.6" with standard journal
 reiserfs: using ordered data mode
 reiserfs: checking transaction log (device ide0(3,4)) ...
 for (ide0(3,4))
 ide0(3,4):Using r5 hash to sort names
 VFS: Mounted root (reiserfs filesystem).
 Trying to move old root to /initrd ... okay
 Freeing unused kernel memory: 72k init
 reiserfs: found format "3.6" with standard journal
 reiserfs: using ordered data mode
 reiserfs: checking transaction log (device ide0(3,1)) ...
 for (ide0(3,1))
 ide0(3,1):Using r5 hash to sort names
 Adding Swap: 393584k swap-space (priority -1)
 sk98lin: Network Device Driver v7.04
 (C)Copyright 1999-2004 Marvell(R).
 eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
 PrefPort?:A  RlmtMode?:Check Link State
 Got EUMBBAR 0xfc000000
 synobios.c(mpc_i2c_init)(1954) i2c_base = fc003000
 synobios.c(1876)target = 32
 I2C? read 0x20
 I2C? read 0x39
 I2C? read 0x31
 I2C? read 0x0
 I2C? read 0x28
 I2C? read 0x8
 I2C? read 0x5
 synobios: load, major number 201
 reiserfs: found format "3.6" with standard journal
 eth0: network connection up using port A
 speed:           1000
 autonegotiation: yes
 duplex mode:     full
 flowctrl:        symmetric
 role:            slave
 irq moderation:  disabled
 scatter-gather:  disabled
 reiserfs: using ordered data mode
 reiserfs: checking transaction log (device ide0(3,3)) ...
 for (ide0(3,3))
 reiserfs: replayed 3 transactions in 0 seconds
 ide0(3,3):Using r5 hash to sort names